VINCO in XTC-mode?

Steve-o · Post by **Steve-o** » Sat May 24, 2003 4:28 pm

Anybody knows how to get it to work WITHOUT using Multi FX S (cause settings will not be stored with song) ??
Help appreciated!
Cheers, Steve-o

Post by **garyb** » Sat May 24, 2003 10:39 pm

does it exist in the vst folder of your sequencer?

Steve-o · Post by **Steve-o** » Sun May 25, 2003 12:33 pm

I put it in there - but there's only *.dev's available after install of Vinco - no dlls. So Vinco is not available from VSTplugins in SX. Hm...

siberiansun · Post by **siberiansun** » Mon May 26, 2003 6:09 am

sounds strange since both spl attacker and optimaster works in xtc mode....
did you try the old worn out solution; remove all vinco files from vstplugins folder, reinstall?

Steve-o · Post by **Steve-o** » Mon May 26, 2003 9:52 am

Yes, Sib, I tried-no success. Attacker has dlls in XTC-folder under VSTPLUGINS. Do you use Vinco in XTC-mode? Anybody?

Post by **garyb** » Mon May 26, 2003 4:13 pm

how about manually copying the .dlls into the vst folder?

mano · Post by **mano** » Mon May 26, 2003 10:04 pm

i have vinco working in xtc mode HOWEVER sometimes it acts a bit weird (it looks like it is off or it disappears!)

Steve-o · Post by **Steve-o** » Wed May 28, 2003 12:04 pm

On 2003-05-26 17:13, garyb wrote:
how about manually copying the .dlls into the vst folder?

SURE - but there aren't any dlls after installation the OXE of Vinco - nowhere!
Strange...

Did you do that?

Steve

<font size=-1>[ This Message was edited by: Steve-o on 2003-05-28 13:05 ]</font>

Post by **garyb** » Wed May 28, 2003 6:48 pm

afaik the dlls are in the sfp installation.you might try reinstalling to make sure that they go in the right folder.i believe you can copy them off the install disk if you want to do it manually.to my knowledge the oxe only authorizes the use of vinco.......

lookmoo · Post by **lookmoo** » Fri May 30, 2003 9:56 am

I can use Vinco S & Vinco M on Cubase SX by
1)copy 2 files ( Vinco S.dev & Vinco M.dev ) to C:SFPDevicesXTC
2) copy some dll files ( i use GRAPHEQ S.dll ) from Cdrom (SFP 3.1c PC ) to youe XTC ( C:Program FilesSteinbergVstPluginsXTCGRAPHEQ S.dll )
3) rename GRAPHEQ S.dll to Vinco S.dll & Vinco M.dll you must make it 2 times for have Vinco S.dll & Vinco M.dll in C:Program FilesSteinbergVstPluginsXTC
4) try to test it on Cubase SX & use it

happy happy happy

Steve-o · Post by **Steve-o** » Wed Jun 18, 2003 5:20 am

Hi lookmoo: can't believe this. I just returned from a 2 week vacancy with my notebook and long awaited Nuendo 2 and couldn't answer earlier.
I'll try out your tip tonite and will report...

Greets and thanks for your help!
Steve

Steve-o · Post by **Steve-o** » Wed Jun 18, 2003 3:37 pm

Do not understand how, but it works!
Great, thank you for your help! Steve