hello, I tried to upgrade to windows 8.1 from 8 ....
and came back to 8.0 ...
anybody was able to do it ?
thank you
windows 8.1 upgrade
Re: windows 8.1 upgrade
Ive got 8.1 running on my non-DAW laptop ok.
Re: windows 8.1 upgrade
I had no problems with it.
Re: windows 8.1 upgrade
with scope drivers without doing anything ?
Re: windows 8.1 upgrade
you need to reinstall the drivers. just rerun the installer.
Re: windows 8.1 upgrade
Just re-install them the way you did in 8.0.maggiau wrote:with scope drivers without doing anything ?
Re: windows 8.1 upgrade
ok thank you, I will try this week-end
Re: windows 8.1 upgrade
oh no !!!
my scope DAW worked better then ever..
with Win8 64bit, sfp 5.1 and ableton .
and i did it .. i installed the 8.1 update .. now my scopes don't want their drivers.
If i run the sfp setup as admin i get:
Found "Sonic Core Pulsar2"
ERROR: InstallDriver returned -2
...
my scope DAW worked better then ever..
with Win8 64bit, sfp 5.1 and ableton .
and i did it .. i installed the 8.1 update .. now my scopes don't want their drivers.
If i run the sfp setup as admin i get:
Found "Sonic Core Pulsar2"
ERROR: InstallDriver returned -2
...
Re: windows 8.1 upgrade
windows8 requires you to turn off driver signing when installing. you had to do this to install the driver in win8 the first time.
my usual cut-n-paste:
windows 8 requires the driver to be signed by microsoft. the Scope driver isn't signed so you must turn off the "feature" that requires this. here are two easy methods to install the driver. i prefer the second one in the link.
========================================
You can permanently enable Test Mode by opening an Elevated Command Prompt and typing the following commands, then rebooting:
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
hit enter after each command. to open an elevated command prompt, use these instructions:
http://pcsupport.about.com/od/windows-8 ... dows-8.htm
To turn it off again, use these commands:
bcdedit -set loadoptions ENABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING OFF
here is a second way to enter test mode:
http://www.fotoclubinc.com/blog/how-to- ... windows-8/
my usual cut-n-paste:
windows 8 requires the driver to be signed by microsoft. the Scope driver isn't signed so you must turn off the "feature" that requires this. here are two easy methods to install the driver. i prefer the second one in the link.
========================================
You can permanently enable Test Mode by opening an Elevated Command Prompt and typing the following commands, then rebooting:
bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
hit enter after each command. to open an elevated command prompt, use these instructions:
http://pcsupport.about.com/od/windows-8 ... dows-8.htm
To turn it off again, use these commands:
bcdedit -set loadoptions ENABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING OFF
here is a second way to enter test mode:
http://www.fotoclubinc.com/blog/how-to- ... windows-8/
Re: windows 8.1 upgrade
ohh .. i remember something like that .. this should be sticky or added in soniccore FAQ..
i really searched before asking here ..
great help & pasting !!
Thanx garry
its rocking again!
i really searched before asking here ..
great help & pasting !!
Thanx garry
its rocking again!
Re: windows 8.1 upgrade
it's a windows thing...