Cubase 3 locked up - Creamware cards unavailable

hairyfriend · Post by **hairyfriend** » Thu Jan 31, 2008 2:16 pm

I was workin on a track in Cubase 3. After loading a plugin Cubase hangs. Then i had to reset my pc because ctrl-alt-del didn't work. When booted started Cubase again and my Creamware cards in Cubase are unavailable.. Not in device manager. But i can load files into Scope. I installed Asio4all and this program says: Beyond Logic. I un&reinstalled Cubase, disabled Creamware cards in device manager XP. Still no Creamware cards in Asio setup. XTC mode is off.. Now.. half an hour later i have Creamware play-rec 1&2 back in Asio setup. Don't know what to do! Cannot switch to Scope Asio driver in Cubase.. Asio Scope could not be initialized!

H-Rave · Post by **H-Rave** » Thu Jan 31, 2008 3:58 pm

When your computer crashed you probably damaged some files, either try a system restore an asio file may have been damaged, or safer to just reinstall scope,and then cubase.I suspect that you think that asio4all will actually do something to help the situation unfortunately it won't.

good luck

hairyfriend · Post by **hairyfriend** » Thu Jan 31, 2008 9:26 pm

Where's the uninstall? The Scope dir is in my root C:\

hairyfriend · Post by **hairyfriend** » Thu Jan 31, 2008 9:56 pm

Deleted files manually from c:\. Dowloaded Scope from Sonic Core. Re-installed Cubase & Scope. Still don't work..

Post by **garyb** » Thu Jan 31, 2008 10:53 pm

what's in the routing window?

H-Rave · Post by **H-Rave** » Fri Feb 01, 2008 2:36 am

Did you try system restore to before it happened ?

hairyfriend · Post by **hairyfriend** » Fri Feb 01, 2008 4:05 am

Tried system restore as first thing. Routing window shows normal behaviour.. Have to reinstall whole pc i think

hairyfriend · Post by **hairyfriend** » Fri Feb 01, 2008 6:05 am

Update: Installed my pc again, all new. installed scope, installed cubase. now i miss 6 outputs. I really don't know what to do. Are the cards broke?

H-Rave · Post by **H-Rave** » Fri Feb 01, 2008 7:14 am

Your samplerate should be on master

hairyfriend · Post by **hairyfriend** » Fri Feb 01, 2008 7:23 am

I have an Behringer DDX3216 which is ADAT master.. i tried..

H-Rave · Post by **H-Rave** » Fri Feb 01, 2008 7:26 am

well you can see that it's not syncronised can't you so obviously the platform won't make any sound, try it on master

hairyfriend · Post by **hairyfriend** » Fri Feb 01, 2008 8:04 am

Anyway, how is it possible that i only see 1-2 in & out on my scope card in Asio setup. First i had 4x stereo in out..

H-Rave · Post by **H-Rave** » Fri Feb 01, 2008 8:09 am

what you see in the asio setup there are the WAVE drivers wich are used to sync the asio there not asio drivers.And I might add that if you don't put wave drivers in your project in to a mixer for example the asio driver can't sync to the scope drivers.you sync the asio setup to the internal soundcard I imagine.

Herr Voigt · Post by **Herr Voigt** » Fri Feb 01, 2008 1:44 pm

Check your connection to the Behringer, check the Behringer itself.
When you haven't a proper master in your chain, your system is completely scrambled, and no drivers available.

Good luck, Thomas

Post by **garyb** » Fri Feb 01, 2008 11:06 pm

you need a matching asio source and destination module in the routing window before opening the sequencer...

i would use a mixer and monitor everything in the scope mixer, that way you'll get zero latency monitoring for everything but vstis, which will have the asio(ulli) latency.