Sending Cubase SX2 Audio Track To Scope Mixer?
I want to send a single audio track from Cubase SX2 into a line in my Scope mixer for using scope processing effects. What is the routing procedure (if that is possible in SX2). I only need to use it for one stereo pair (other than the main stereo pair that defaults into Scope). I know SX3 has more easy ways of doing this, but right now SX2 is what I have for now. I was recomended by a friend to use the senderella plug in found in this forum http://www.planetz.com/forums/viewtopic ... &forum=3&6 is that the way to go? Any suggestions? Thanx!
-
Liquid EDGE
- Posts: 1205
- Joined: Sun Apr 04, 2004 4:00 pm
- Location: Brighton England
- Contact:
yep as wayne says..
set asio source to as many channels as needed (1+2 being left and right master..3+4 left and right bus ..and so on). then in sx2 busses will pop up.
press f4 to see the master/buss outputs.. TURN THEM ON.. then send the regular channels in sx mixer (f3) to wotever buss. This is done by clicking on the bottom part of a channel, a list of enabled busses, groups ect will apear and select desired route. if only mono cha, pan to left or right of bus. e'g pan to left which will go to 3 in the asio source in scope, send number 3 of asio source to a mono input in scope mixer..
hope that makes sense
oh and one thing that comes to mind. wot i do is use busses after the master output to go to the scope mixer and leave the master output free for bouncing duties, as sx2 can only bounce(audio mixdown) through the master out.
so if computer cpu starts to stress out i will select, say, the most hungry synth in sx.. solo it, re-asign to master out put.. bounce it down. then send the created audio channel to where the orig synth was routed to. then turn the synth in question off.
god i woffle on..
with all i've just said.. i read through your post again and mabye all you should do is use xtc mode, but this will cut down on a lot of posibilities
_________________
Keep Rollin'
http://www.mutationrecords.co.uk
<font size=-1>[ This Message was edited by: Liquid EDGE on 2005-03-02 01:49 ]</font>
<font size=-1>[ This Message was edited by: Liquid EDGE on 2005-03-02 01:54 ]</font>
set asio source to as many channels as needed (1+2 being left and right master..3+4 left and right bus ..and so on). then in sx2 busses will pop up.
press f4 to see the master/buss outputs.. TURN THEM ON.. then send the regular channels in sx mixer (f3) to wotever buss. This is done by clicking on the bottom part of a channel, a list of enabled busses, groups ect will apear and select desired route. if only mono cha, pan to left or right of bus. e'g pan to left which will go to 3 in the asio source in scope, send number 3 of asio source to a mono input in scope mixer..
hope that makes sense
oh and one thing that comes to mind. wot i do is use busses after the master output to go to the scope mixer and leave the master output free for bouncing duties, as sx2 can only bounce(audio mixdown) through the master out.
so if computer cpu starts to stress out i will select, say, the most hungry synth in sx.. solo it, re-asign to master out put.. bounce it down. then send the created audio channel to where the orig synth was routed to. then turn the synth in question off.
god i woffle on..
with all i've just said.. i read through your post again and mabye all you should do is use xtc mode, but this will cut down on a lot of posibilities
_________________
Keep Rollin'
http://www.mutationrecords.co.uk
<font size=-1>[ This Message was edited by: Liquid EDGE on 2005-03-02 01:49 ]</font>
<font size=-1>[ This Message was edited by: Liquid EDGE on 2005-03-02 01:54 ]</font>