PlanetZ forums - scopeusers.com

P.S.
and MIDI source module connected to sequencer dest modul too,

BTW, How are you rodos1979, you are always near me

Try this,
pull down MIDI channel strip/ SENDS and change field "NOT CONNECTED" to CREAMWARE MIDI 1 or 2 and next field "ANY" will be MIDI channel number. It should be OK now, I have solved that problem like this, when I use XTC synths thru the SFP.

1. Only swap two of Pulsar cards?
I have tweak now cset.ini with intBlkSize=512. This is 13 ms latency. Enything down from 512 is cset.ini instalation error. But now ...ACCELERATOR... mesage is gone. I think that there is error because cset.ini load Pulsar 1 first even in the order in my SFP window ...

1. First of all I have Pulsar 2 only (slot 3), working in XTC and in SFP mode without problems. Then I have put Pulsar 1 (slot 4)with STDM cable (total 10 processors) and then "XTC CAN'T WORK IN ACCELERATOR MODE". I have tweak all of things that I have readed here, tweaking cset.ini for changing ...

Hi Vasili and at0mic too.

I have my Pulsar 2 in slot 3 and Pulsar 1 - slot 4, so I suppose that my Pulsar 2 is master now. SFP 3.1c is instaled and DSP meter said that I have 10 DSP. But seems that P2 isnt master because of "accelerated mode" message, so I need close instruction how to set master ...

I have eddited my message, but you are faster at0mic :smile: so please answer me again. I think that I have answer now but, please confirm my question again?

How wil know which board is master, or only change settings in cset.ini like this

[board0]
boardid=1

change to

[board0]
boardid=0 for ...

So, can I use XTC mode when I set Pulsar 2 as master card and ULLI 13ms or higher or there is no way to use my DAW in XTC mode?

If not possible, any options, something with *.ini files or some other way to baypass Pulsar 1 card, without removing Pulsar 1?

BTW, don't know how to set Pulsar 2 to be ...

My Pulsar 2 works perfect in SFP and XTC mode, but when I instal Pulsar 1, XTC mode can't be loaded.
Some kind of "XTC can't be loaded in acceleration mode" message was displayed.

What does it mean?

:smile:
No. Kompas is the name of my band but not related to music style but nautical compass
We play varyous styles of music. In my country cyrilic letter is basic and compass is the same with kompas, and reading is:

Read like you write, and write like you read.
Maybe it is strange for you, but ...

So, I can use SFP 3.01c from Pulsar 2 with Pulsar 1 too, but mast register for software keys???

I have Pulsar 2 and now another Pulsar 1. Cann I use SFP 3.01c registered to Pulsar 2 with Pulsar 1 in another PC, or what I have to do?

Everything fine now.

I have set ADAT to Direct OUT and MULTICHANNEL OUTPUT from DDX3216 to MASTER OUT, then ADAT A and B DEST modules OUT to Dynamic Mixer (8 stereo = 16 mono channels), and than MIX OUT from Dynamic mixer (2 channels L and R) to ASIO DEST module.

Yes, but strange for me:) I am new in DAW world and still learning. But I will try that

Yes, but maybe my question is not good. I mean , is it possible doing mix down within external mixer FX's using ADAT channels?

For some reason I haven't any audio signal back to my pulsar 2 adat in. Maybe the answer is in routng external mixing console.

>There's certainly a multi-channel recording bus you can route to an Adat out.

There is answer I think

Thanks

On 2003-04-13 09:29, astroman wrote:
no, I don't think Pulsar One's S/PDIF is unreliable, though the implementation in Pulsar Two is better.
The problem comes from the S/PDIF definition itself, that the sender must be master and receiver slave (basically) which may conflict with the Adat sync ...

Can I mix down my material (Cubase SX) out from my digital Behringer DDX3216 within DDX3216 FX to ADAT IN using diferent modules wiring, like ASIO SOURCE to ADAT DEST module, whatever, Pulsar 1 or Pulsar 2 wired with STDM cable?

On 2003-04-12 19:56, astroman wrote:
Pulsar one has RCA but it isn't exactly fun if you use it together with the Adat ports.
You might run into trouble between Adat and S/PDIF sync - at least I did.
It was so wiered I didn't even try to understand what was going on.
I use an old Korg 168 ...

On 2003-04-12 08:37, ghandi wrote:

I have a configuration with two pulsar I and a pulsar II card in one pc. No problems, everything works fine!

Can you use I/O from both cards simultaneously?

I am interersted for ADAT I/O and S/PDIF from Pulsar 1 because my Pulsar 2 is with AES/EBU.

On 2003-01-11 04:19, One2Waziru wrote:
I am still using a pulsar1 card togheter with an xtc card .
I just wonder if i will get full use ulli with cubase sx if I ad a luna2 or will the pulsar 1 card block me from this?


Do you have tried to put two Pulsars in your PC?

I am planning to connect ...