PlanetZ forums - scopeusers.com

So, I have signal in the 14 channel but signal wont go to the master channel?

That's weird shit. I can't help, but g'day Sandro, been a long time mate

corrupt project?
something missed, pilot error?
bad s/tdm cable(if there are multiple cards)?

Just one Pulsar card. I don't have error messages. Everything looks normal, but sound wont go to the master channel. All others channels work normal.

this is pic

14 channel wont work... And the others ?

Is the green "mix" button on, on each channels ? Did you try another mixer ? Delete it and reload it ? Do you get sound at the direct outputs ?

JoPo wrote:14 channel wont work... And the others ?

Is the green "mix" button on, on each channels ? Did you try another mixer ? Delete it and reload it ? Do you get sound at the direct outputs ?

I have sound on direct output.
which mixer you recomend. I need 16 chanels with direct outs and 1 aux.

I have strange behavior here.
So, When I reload mixer and just set 14. channel to STEREO then I have sound from that 14. channel on master channel.
But when I set 13. channel to STEREO, then 14. channel wont go to mix.
then I set back 13. channel to MONO but 14. channel stil wont work properly.

That does sound strange. Perhaps a file got corrupted. Did you try doing a reinstall over the top of your existing scope installation. That should then replace any files which might have become corrupted. Perhaps see what the others think about this before you try it though as I wouldn't want to suggest anything that might cause further problems. But if you do decide to, remember to back up any preset files if you created your own presets. But other files such as 3rd party devices or modules will not be affectd as the reinstallation only overwrites the Scope OS files. I think this is correct, and hope that works for you.

Yeah ! Good idea. I would try that. Run the Scope installer !

I did whole unistalation includeing drivers, then I did new instalation but didn't help.
If the only 14. channel is stereo then works ok, but when I set 13. channel to stereo than 14. channel wont route to mix.
... and I can't force 14. channel to work properly anymore, even if I set back 13. channel to mono.

weird. never heard of that, but why not use the stm2448? it doesn't use significantly more resources.

garyb wrote:weird. never heard of that, but why not use the stm2448? it doesn't use significantly more resources.

STM1632 is exactly what I need in all my projects, because I use Pulsar just for routhing and monitoring.
If I remeber well stm2448 don't have direct outs?


BTW: When I'm already here and you are helpfull (thanks), my Wave Destination wont record properly. I have very distorted sound. ASIO Destination works nice, but I will like to use Wave Destination to record in some cases.
?

sure, the 2448 has direct outs.
64bit? the wave input just doesn't work.

garyb wrote:sure, the 2448 has direct outs.
64bit? the wave input just doesn't work.

thanks.
Yes. 64bit.

Very strange, indeed !

Here, I had some strange STM direct output behavior ! But you should simply try... If you just need a mixer with direct output, so, faders on each channels, you can use 'channel' module... And for the aux, a little mixer like micro / dynamic mixer or free ones. This could be dsp power saving...

I think 'channel' module from Scope install won't work with midi automation... But S|C send me a fixed version years ago, if someone needs.

JoPo wrote:Very strange, indeed !

Here, I had some strange STM direct output behavior ! But you should simply try... If you just need a mixer with direct output, so, faders on each channels, you can use 'channel' module... And for the aux, a little mixer like micro / dynamic mixer or free ones. This could be dsp power saving...

I think 'channel' module from Scope install won't work with midi automation... But S|C send me a fixed version years ago, if someone needs.

Thanks
Yes. I need just about maximum 16 channels with direct outs and sometimes just 1 reverb on aux.
I did startup project useing STM 1632 but I leave 13. channel mono, and then 14. channel working well.