Page 1 of 1
looking for an easy way to check all used CC's in project
Posted: Sun Mar 29, 2009 12:13 pm
by irrelevance
Is there a way of finding all cc's used across different devices? The only way I know at the moment is to manually open each device's midi ctrl assignment and check what is used/not used, then on to the next device. Would be great if there was a way to find out which cc's are open to use.
Re: looking for an easy way to check all used CC's in project
Posted: Sun Mar 29, 2009 12:32 pm
by dawman
I wish.....
I have a Notepad for each project that shows the assignments.
Scope doesn't remember half of them, so I just write them all down.
Once there are re assigned though they work great until another project gets loaded.
Re: looking for an easy way to check all used CC's in project
Posted: Sun Mar 29, 2009 3:47 pm
by eric
I also notice you cant assign the same MIDI contoller number to more than one control. That's in Modular 2 anyway.
I guess you just cross-map/remap it in a MIDI processor and send the duplicate control messages on a different controller number - messy.
Eric.
Re: looking for an easy way to check all used CC's in project
Posted: Sun Mar 29, 2009 5:23 pm
by dawman
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 4:04 am
by eric
Downloaded. Will give it a try.
Thanks Jimmy V.
Eric.
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 5:51 am
by dawman
They are confusing at first but here's an example.
untitled.JPG
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 7:04 am
by Neutron
if you merge everythings midi output and then put a midi monitor on the merged output, it might show them when you reopen the project.
i never tried it though. the reason i think it might is because when i open a project all the pot positions are sent to bcr2000
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 9:08 am
by irrelevance
Neutron wrote:if you merge everythings midi output and then put a midi monitor on the merged output, it might show them when you reopen the project.
i never tried it though. the reason i think it might is because when i open a project all the pot positions are sent to bcr2000
That's a very good idea! I was thinking of ways to somehow trigger devices to spit out the information but you may well be right about the midi output at project load. Will report back!
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 9:18 am
by irrelevance
BRILLIANT IT WORKED!
So after the project has loaded I can disconnect the midi outs and merger and keep the midi monitor open as a reference to all currently used cc's.
Neutron you are a star...
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 9:22 am
by irrelevance
Ok spoke too soon on deleting the connections and merger. On reload the monitor is empty which must have something to do with temporary buffers being cleared. Oh well a merger doesn't cost to much dsp
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 9:30 am
by Neutron
cant you copy and paste them in to a notepad? i dont know if midi monitor is copyable, since i never tried.
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 9:34 am
by irrelevance
Yes. I just hooked up midi-ox which allows for input monitoring and will copy to clipboard.
Re: looking for an easy way to check all used CC's in project
Posted: Mon Mar 30, 2009 9:42 am
by Neutron
cool, you can use one of spacef notepads to have the info attached to the project.