Page 1 of 1
Posted: Thu Mar 02, 2006 1:39 pm
by FG445
Hi there,
first of all - sorry for a new Topic for such a small question
Now my question:
I want to route the signal of my first channel strip in the dynamic mixer to the output 1l/1r. Now , how can i route the signal just there , so that it is not going through the mainmimx channel?
I hope u get my problem , it should be easy , right?
Best
Daniel
Posted: Thu Mar 02, 2006 3:21 pm
by virtualstudio
unclick the green button
Posted: Thu Mar 02, 2006 3:59 pm
by FG445
alright , this sounds easy...
But which green Button do u mean?
I don´t see any green Button.
Maybe this is totally stupid
But please help me anyway....
Cheers
Daniel
Posted: Thu Mar 02, 2006 4:23 pm
by virtualstudio
sorry to quick, I was thinking about stm mixers
Posted: Thu Mar 02, 2006 4:40 pm
by FG445
is this possible with the dynamic mixer at all?
To route the signal from one channel ago the sum channel?
Posted: Thu Mar 02, 2006 9:08 pm
by wayne
You may have to use STM 1632 (with green 'send to mix' button)
Posted: Fri Mar 03, 2006 10:01 am
by FG445
there is a point in the manual which says :
turn off the "mix" button...
the overview of the manual points to page 8 for that...
Either i am stupid or the guys who wrote that manual are...
There is nothing about such a knob on that page neither on this, nor on any other page of the "dynamic mixer" manual..
Can someone clearify this???
Best
Daniel
<font size=-1>[ This Message was edited by: FG445 on 2006-03-03 10:03 ]</font>
<font size=-1>[ This Message was edited by: FG445 on 2006-03-03 10:03 ]</font>
Posted: Fri Mar 03, 2006 10:37 am
by wayne
OK. You can't do what you want to do on the dynamic mixer. Use another one, or just route differently.
Posted: Fri Mar 03, 2006 1:23 pm
by djmicron
On 2006-03-03 10:01, FG445 wrote:
there is a point in the manual which says :
turn off the "mix" button...
the overview of the manual points to page 8 for that...
Either i am stupid or the guys who wrote that manual are...
There is nothing about such a knob on that page neither on this, nor on any other page of the "dynamic mixer" manual..
Can someone clearify this???
Best
Daniel
>
this is not from the dynamic mixer manual.
Posted: Fri Mar 03, 2006 1:25 pm
by FG445
awwwwww,
shit. because the dynamic mixer is the only one with that much individual outs...
The other mixers work with just a few sum busses. This is really bad. I think this should be possible with the dynamic mixer. Because, when i route the signal into my host application from the mainmix, i have lets say the bass going into my host over the mix output. When i now want to route that bass over an individual out into the host, to eq it there, then i have the signal doubled there. I dont want this channel - here the bass ch strip - in my mix out...
How can there be a mixer with individual outs when one cannot route the signal from one channel ago the mix channel to a seperate out???
Thanks wayne , btw
Can one help me to get my feet on the ground here ?
Best
Daniel
Posted: Fri Mar 03, 2006 1:44 pm
by garyb
both the stm1632 and 2448 have direct outs on every channel.
Posted: Fri Mar 03, 2006 1:55 pm
by ARCADIOS
there is a small litle botton in 2448 and 4896 that if you press it, the direct outs will appear. the botton is called "direct outs".
press it
Posted: Sat Mar 04, 2006 7:34 am
by FG445
alright, thanks thanks - now the show can go on
Have a nice weekend!
Cheers
Daniel