Page 4 of 4
Re: CMS-1
Posted: Sun Nov 18, 2018 7:36 am
by t_tangent
Thanks Roy, I will have a look later on. Appreciate the help
Re: CMS-1
Posted: Fri Dec 10, 2021 1:50 am
by Liquid EDGE
roy thinnes wrote: ↑Thu Sep 20, 2018 9:24 am
No, you just need to install the setup as metioned in the first post.
If you run into any problems, just ask
Hi Roy,
I finally went to try cms-1
I installed scopesync-v0.6.0.62 and also ScopeOSC-v0.1.4-beta then installed CMS-1 v0.1.0.62.
When I go to load it in scope I get a can’t find cms-1 1.0.1 dsp (or something very similar)
Do you have this file please? There is no CSM-1 dsp file in my dsp folder..
Re: CMS-1
Posted: Sat Dec 11, 2021 7:21 am
by Liquid EDGE
Or, whoever has this working does anyone have this dsp file?
Scopesync and bcmodular are working fine, so by all accounts CSM-1 should work fine for me..
Oh, this is on my xp32bit.
Re: CMS-1
Posted: Sat Dec 11, 2021 7:22 am
by Liquid EDGE
Also, just to confirm
Is scopesync and also CMS-1 fine on a 64bit system?
Re: CMS-1
Posted: Sat Dec 11, 2021 8:12 am
by w_ellis
Sorry, it's been three years now since I last looked at this, so I'll have to do a bit of catching up myself
Did you use the Windows Installer to install CMS-1? Theoretically that should walk you through all of the steps to choose the right directories to install stuff, including dependencies like the C++ redistributable. There is a Zip file version, but it's definitely more complicated to install manually.
32-bit and 64-bit should both work fine, also for the VST plugin versions both in VST2 and VST3. I know a lot has changed in VST3 support in the last couple of years though, so let me know if anything has stopped working.
Re: CMS-1
Posted: Sat Dec 11, 2021 8:16 am
by w_ellis
By the error message, I would suggest that the DLL file didn't end up in the right place in the Scope directory. If you have Scope installed in a non-standard place, you need to tell the installer, so it knows where to put it.
Re: CMS-1
Posted: Sat Dec 11, 2021 8:20 am
by w_ellis
When I run the installer on this Windows laptop, this is what ends up in my Scope PCI folder:
- cms.png (7.11 KiB) Viewed 12126 times
Re: CMS-1
Posted: Sat Dec 11, 2021 8:45 am
by Liquid EDGE
Thanks, I’ll have a look into it.
I’m sure I have the most up to date installers for all bits
I used the installers for each part. Scopesync/scopeOSC/CMS-1…
It’s for my Xite-1, incase that makes any difference?
Re: CMS-1
Posted: Sat Dec 11, 2021 8:51 am
by w_ellis
Try running the cms installer again and pay close attention to the directories tab. Do you see that dll file in your scope xite/app/dll folder?
Re: CMS-1
Posted: Sat Dec 11, 2021 12:00 pm
by Liquid EDGE
Yeah it’s there..
Installed again as well.
Re: CMS-1
Posted: Sat Dec 11, 2021 1:37 pm
by w_ellis
Strange! I assume you've tried the obvious things, like restarting scope and/or your pc?
Other things that could be a problem would be if the c++ redistributable didn't install properly or if you have a firewall that is blocking the dll.
Re: CMS-1
Posted: Sat Dec 11, 2021 1:46 pm
by Liquid EDGE
w_ellis wrote: ↑Sat Dec 11, 2021 1:37 pm
Strange! I assume you've tried the obvious things, like restarting scope and/or your pc?
Other things that could be a problem would be if the c++ redistributable didn't install properly or if you have a firewall that is blocking the dll.
Yeah, I’m a bit perplexed.
I’m having the last thought.
Thanks though.
Re: CMS-1
Posted: Sun Dec 12, 2021 7:01 am
by Liquid EDGE
Right, what I’m finding is that only scopesync 1.0.1 .dll & (vst) is the only scope sync working on my XP32bit set up, anything else does not get found. Generates a “can’t find blah blah dsp” and the only scopesync related VST that shows up in cubase is scopesync1.0.1
What was all this stuff written on?
I know xp is a dinasour of an OS so that’s what I’m putting it down to…. So I’m guessing that the CMS-1 files want/tweaked/use scopesync AFTER 1.0.1….
(I’m sure I had a working CMS-1 on xp, but I’m sure it was the first/very early version of it, not sure, can’t remember fully)
Total assumption here…
When I get time and after I’ve cloned my win1064bit hard drive I’ll install all the latest versions of scopesync/scopeOSC/CMS-1 and see how it gets on there.