PlanetZ forums - scopeusers.com

i've received this message:

welcome to Sonic Core.

64 Bit drivers are in internal testing at the moment and
will come out in about one month.

OSX we may have in about 6 months.



--
Mit freundlichen Grüßen / Kind regards
Dipl.-Ing. Ralf Dressel

hi,
well i 've just wanted to say something...
first of all my problem was the background noise (we call it deepnoise here) even if the card in null (no cable connected even its own cable)
then i 've learned scope and rme structure very different and rme 's already grounded but scope not (i 've ...

ok my bad sorry.

If you have an RME card with an adat port, connect that to Scope & route the signal over to the RME...

If not there are other meters on the market that do RMS+peak with numeric readout.

yep brilliant idea but signal could be filtered (+4/-10/lo gain).expect 3-6db clean signal.


i meant rme ...

one of my friend told me that there is a regulator chip on scope and it could be produce noise if badly soldered or wrong chip used wrong country. it is on the card dsp's opposite side or i can say left bottom side. we searching on the internet but we could not find to chip for purchase. it is put ...

yes but you can try others for scope.at least if you have sound forge you can record silence and also you can check levels from scope's mixer but still everything illogical if you can hear noise(s) with you ears.

set everything off or disconnect from card (s). use digicheck, vumeter, rme/scope mixer to see level, also try to record silence and most important use your ear.

btw little ground loop isolator really works there is appr. 7db between direct connection with it. im really surprised.

i've decided to use rme,at least for now,card itself grounded and all inputs very silent.i can sell scope.

no just one toslink cable goes from scope to sb audigy nx. if i connect this cable scope's b i hear sound, if i connect scope's other digital out i hear nothing. that's all. you know there are 2in-2out digital.

valis wrote:Show the FULL window please, not just that setting.

ok here it is full. this config ok for adat b but adat a does not work. if i select opt.adat on samplerate settings window, all sounds stop.look below; or

no signal goes to soundblaster not coming. it goes with toslink cable.
when i select it like the picture nothing heard.

you mean this? if i set like this i hear no sound at all.

where?

this is working if i connect toslink cable to adat b. if i connect adat a, don't work.

valis wrote:Skip the expander.

Tell me again what is connected to the card's XLR inputs?

skipped expander and all default. classic i/o no xlr in/out. rca plugs.
nothing connected currently. toslink in/out (adat a) not working, b is ok.
except adat a and analog source noise remains ok.

valis wrote:Do us a favor and post up a pic without the expander, and without the -12db input gain (leave the channel's input at 0.0)

hello everybody,i have to say all of you very helpful people which i didnt expect much.
my opinion, scope best of the best audio card. some people comparison with m-audio :) from my country funny isnt it?

anyway, thank your opinions and ideas.

i use my compressor on digital a and blew up ...

yep -100 usual nice, -90 not bad but what about -68 to -82 no no sir not good.im very dissapointed.mine is mostly -78 which is not good we can say bad very bad. my Luna was better.

Ok here's another perspective. With the analog in set at 0 and the L-R set at zero I get the noise that was bothering me. However, I just did some measurements on that noise, and it turns out I'm still getting 80.77 dB signal to noise. Not as good as some of my other equipment, but really it's not ...