Hi
Sending audio Ramp to Flexor
I manage that from Cubase : one cycle ramp on each bar and it work!
So I did bounce that ramp to a file : 120bpm_1Bar
load it in Renoise in the sample player = not working
Then in a sampler : Bliss, Independence, Falcon = not working
Any body any ideas ?
Thanks
Send audio Ramp to Flexor from Renoise
- ChristianB
- Posts: 68
- Joined: Thu Feb 10, 2005 4:00 pm
- Location: Montréal
- roy thinnes
- Posts: 651
- Joined: Thu Jan 09, 2003 4:00 pm
- Location: Graz
- Contact:
Re: Send audio Ramp to Flexor from Renoise
controlling Modular sequencers externally (by sending a Ramp signal from your DAW) works quite perfect.
Give the Ramp signal a specified Asio output, connect it to Modular, and you're good to go (but be careful not to connect it to the audio mixer, otherwise you'll ruin your headphones/speakers).
Depending on your DAW, you'll probably have to check what time stretch method is most appropriate to have a tight rhythm.
If nothing is happening on the Modular side you have a connection problem (check the Modular input signal with a ValMeter module).
Give the Ramp signal a specified Asio output, connect it to Modular, and you're good to go (but be careful not to connect it to the audio mixer, otherwise you'll ruin your headphones/speakers).
Depending on your DAW, you'll probably have to check what time stretch method is most appropriate to have a tight rhythm.
If nothing is happening on the Modular side you have a connection problem (check the Modular input signal with a ValMeter module).
- ChristianB
- Posts: 68
- Joined: Thu Feb 10, 2005 4:00 pm
- Location: Montréal
Re: Send audio Ramp to Flexor from Renoise
HI Roy
It is perfect I agree !!!
But
Renoise is refusing to send it properly.... Cubase fine, Samplitude fine, etc
I'm starting a project and Renoise is the best for doing the job... but no Ramp
It is perfect I agree !!!
But
Renoise is refusing to send it properly.... Cubase fine, Samplitude fine, etc
I'm starting a project and Renoise is the best for doing the job... but no Ramp
-
- Posts: 1638
- Joined: Mon Nov 15, 2010 12:57 pm
Re: Send audio Ramp to Flexor from Renoise
Do you see the waveform properly? Maybe in saving the ramp as wave, something is bad.
You can generate a sawtooth wave, use a simple LFO, or synth to send the audio ramp, just tune it to 2Hz for 120bpm and capture the wave again.
You can generate a sawtooth wave, use a simple LFO, or synth to send the audio ramp, just tune it to 2Hz for 120bpm and capture the wave again.
- ChristianB
- Posts: 68
- Joined: Thu Feb 10, 2005 4:00 pm
- Location: Montréal
Re: Send audio Ramp to Flexor from Renoise
I just got back to that project yesterday
And... After spending couple of hours trying this and that,
I found that in Renoise on the Master track, the DC filter check box was tick !!!!!
I felt stupid
but then I was surprise that the DC offset is apply to all outputs not just the master.
Happy Renoise user now!!! I got an audio Ramp to MODular IV, from 30 to 999 bpm without having to change anything !
Cheers
And... After spending couple of hours trying this and that,
I found that in Renoise on the Master track, the DC filter check box was tick !!!!!
I felt stupid
but then I was surprise that the DC offset is apply to all outputs not just the master.
Happy Renoise user now!!! I got an audio Ramp to MODular IV, from 30 to 999 bpm without having to change anything !
Cheers