How Could I Make A Tap Tempo Delay....

Anything about the Scope modular synths
Post Reply


User avatar
garyb
Posts: 21182
Joined: Sun Apr 15, 2001 4:00 pm
Location: ghetto by the sea

Re: How Could I Make A Tap Tempo Delay....

Post by garyb » Tue Aug 19, 2014 8:11 pm

a tap tempo delay is just several short delays at times that are nice divisions of the tempo with pan controls.

there's a pattern delay in Scope...

dawman
Posts: 12878
Joined: Sun Jul 24, 2005 4:00 pm
Location: PROJECT WINDOW

Re: How Could I Make A Tap Tempo Delay....

Post by dawman » Tue Aug 19, 2014 9:34 pm

Correct, I meant a Delay that I could actually Tap the tempo to since I only need to get an approximation....

ANkyu

User avatar
garyb
Posts: 21182
Joined: Sun Apr 15, 2001 4:00 pm
Location: ghetto by the sea

Re: How Could I Make A Tap Tempo Delay....

Post by garyb » Wed Aug 20, 2014 1:16 am

oh.
SDK..

User avatar
dante
Posts: 3700
Joined: Sat Nov 24, 2001 4:00 pm
Location: Melbourne Australia
Contact:

Re: How Could I Make A Tap Tempo Delay....

Post by dante » Wed Aug 20, 2014 4:06 am

SDK - well, in that case, first question developer might ask ....

What exactly do you want to tap ?

..... a mouse button....or a touch screen .... or a pedal ?

dawman
Posts: 12878
Joined: Sun Jul 24, 2005 4:00 pm
Location: PROJECT WINDOW

Re: How Could I Make A Tap Tempo Delay....

Post by dawman » Wed Aug 20, 2014 4:35 am

QuNexus or BCF 2000, even PX-3 controller using note on/offs.

jksuperstar
Posts: 1475
Joined: Mon Nov 15, 2010 12:57 pm

Re: How Could I Make A Tap Tempo Delay....

Post by jksuperstar » Wed Aug 20, 2014 7:34 am

Hmmm, I think a sawtooth(ramp) LFO set at the right rate to match scope frequency signals vs. time, and a note on signal to both capture the LFO into a sample/hold, and also hard sync reset the LFO...if you were trying to get midi clock it is definitely anSDK job, but control of delay via frequency signal is doable in modular.

A filter on the sample/hold output could give you averaging, too.

If you use ModIV with a clock from the DAW, you can use the modIV clock VST with the special module, and you'll get a frequency signal output. Then just do tap tempo in the DAW as you always do.
Last edited by jksuperstar on Thu Aug 21, 2014 6:09 am, edited 1 time in total.

dawman
Posts: 12878
Joined: Sun Jul 24, 2005 4:00 pm
Location: PROJECT WINDOW

Re: How Could I Make A Tap Tempo Delay....

Post by dawman » Wed Aug 20, 2014 8:41 am

There ya' go. I will now consult the manual for Bidule and see if this is do-able.
I could always store bpm as a preset too, butin accordance to the crowd reaction, alcohol and drugs consumed by players, the bpm varies....

User avatar
dante
Posts: 3700
Joined: Sat Nov 24, 2001 4:00 pm
Location: Melbourne Australia
Contact:

Re: How Could I Make A Tap Tempo Delay....

Post by dante » Thu Aug 21, 2014 2:40 pm

You could map tempo to pitch bend, then as patrons get drunk, bend the tempo up or down to exaggerate the effect of the intoxicant, depending on whether it's speed or booze. If it's roofies or other combos, you could add in CCx2 :lol: :lol: :lol: :lol:

jksuperstar
Posts: 1475
Joined: Mon Nov 15, 2010 12:57 pm

Re: How Could I Make A Tap Tempo Delay....

Post by jksuperstar » Thu Aug 21, 2014 3:26 pm

Sounds like Brian Eno's next solo album..."music for rufies".

Post Reply