SDK 6 installation
SDK 6 installation
Greetings, I am installing SDK 6 and it leaves a message to me
ROCAtom:: error
cannot load sim.dll
after ok it leaves another message
ROCAtom:: error
c: /program you case out/scope6 sdk xite (x64) /app/bin/sim2k
and finally
Cannot start SCOPE
Could not gain Access to the SCOPE hardware!
can somebody help me?
Thank you very much!!!
ROCAtom:: error
cannot load sim.dll
after ok it leaves another message
ROCAtom:: error
c: /program you case out/scope6 sdk xite (x64) /app/bin/sim2k
and finally
Cannot start SCOPE
Could not gain Access to the SCOPE hardware!
can somebody help me?
Thank you very much!!!
Re: SDK 6 installation
you can only have 14/15dsp cards or an XITE. SDK doesn't work with smaller cards in the computer.
Re: SDK 6 installation
is this when you try to import the key?
Re: SDK 6 installation
No this is when I attempt to open the SDK 6 application.
Re: SDK 6 installation
I'm also experiencing the exact same issue. I'm using Win 7 64bit.
I haven't had time for trouble shooting yet.
I haven't had time for trouble shooting yet.
Re: SDK 6 installation
I have sent a mail to the support of sonic Core and I hope of answer.
Re: SDK 6 installation
I did mail them and got the following response :
Quick note for those who have SDK 6 running - do any of you use Win 7 64bit?
But i didn't had time for any further investigation, so if you find a solution it would be highly appreciated.are you running the SDK "as administrator"? (right click on the SDK icon, choose "run as administrator", answer "yes" to the warning message asking if it's ok to allow SDK to make changes to the system)
Scope is closed while running SDK, yes?
Quick note for those who have SDK 6 running - do any of you use Win 7 64bit?
- Roland Kuit
- Posts: 670
- Joined: Fri Dec 28, 2012 1:42 pm
- Location: NL/SWE
- Contact:
Re: SDK 6 installation
I don't run it on W7, 64 bits, my new laptop doesn't have a card slot. So I'm running it on 2 Vista laptops 32 bits.
I had some problems. SDK6 quitted by deleting modules. After Gay's advice to install and run it as an Administrator those problems were solved.
I had some problems. SDK6 quitted by deleting modules. After Gay's advice to install and run it as an Administrator those problems were solved.
Avant-electronic composer | synthesis research | lecturer
http://www.rolandkuit.com/
http://www.rolandkuit.com/
Re: SDK 6 installation
the current 64bit download may have a problem.
i'm on it...
i'm on it...
Re: SDK 6 installation
I had the same problem on initial installation of SDK6. I assumed from this discussion that there was no solution, so chatted to Holger about it. Anyway, a couple of days later I accidentally launched the SDK6 and it worked fine. No idea what changed in the meantime, could have just needed a reboot, or maybe running it as Administrator fixed something that then needed a reboot. Either way, it loads up fine now.
For reference, I'm on Windows 7 64bit. Also, I chatted to Holger about the remove module bug, which he is aware of and hopes will be fixed soon.
For reference, I'm on Windows 7 64bit. Also, I chatted to Holger about the remove module bug, which he is aware of and hopes will be fixed soon.
Re: SDK 6 installation
Win7 x64 worx here
good vibes
good vibes
Re: SDK 6 installation
can you explain a little better?tgstgs wrote:Win7 x64 worx here
good vibes
It is not possible to use it for all the other users.....
Re: SDK 6 installation
Not all, it works fine now for me, although I experienced the same issue when I first tried to use it.
Only things that happened between it not working and it working were the following (not necessarily in that order!):
- I ran it in Administrator mode (although it didn't work in that mode originally)
- I ran Scope 5.1
- I rebooted the machine (possibly a few times)
I have Xite-1 and Win7 64bit
Only things that happened between it not working and it working were the following (not necessarily in that order!):
- I ran it in Administrator mode (although it didn't work in that mode originally)
- I ran Scope 5.1
- I rebooted the machine (possibly a few times)
I have Xite-1 and Win7 64bit
Re: SDK 6 installation
what i get on win 64 bit when starting sdk 6 in administrator modew_ellis wrote:Not all, it works fine now for me, although I experienced the same issue when I first tried to use it.
Only things that happened between it not working and it working were the following (not necessarily in that order!):
- I ran it in Administrator mode (although it didn't work in that mode originally)
- I ran Scope 5.1
- I rebooted the machine (possibly a few times)
I have Xite-1 and Win7 64bit
I'll try to run scope 5.1 even if i don't see the relationship between this and sdk 6 problem....ROCAtom::error
cannot load sim.dll
then after accepting the error:
ROCAtom::error
c:/program files (x86)/scope6 sdk xite(x64)/app/bin/sim2k
then
Cannot start SCOPE
Could not gain access to the SCOPE hardware
Re: SDK 6 installation
Actually I could be lying. I do remember fannying around with .dll files that looked a bit like sim.dll and renaming them to see if that was the issue. However, at the time it didn't fix it. Maybe it required fannying followed by a reboot.
Re: SDK 6 installation
no reboot or whatsever_
sim2k.dll is in app/bin folder as well as in app/converter5_1
what does a search in explorer vibes tell you?
sim2k.dll is in app/bin folder as well as in app/converter5_1
what does a search in explorer vibes tell you?
Re: SDK 6 installation
Hi Thomas,
Are you using SDK6 with Xite-1?
Thanks,
Will
Are you using SDK6 with Xite-1?
Thanks,
Will
Re: SDK 6 installation
But note that the error displayed is "cannot load sim.dll", not sim2k.dll