Page 1 of 1
Very positive response from support.
Posted: Tue Jan 29, 2013 2:39 pm
by Liquid EDGE
I sent this to support.
............................
Hi
pattern seq, mds8 modular bug. These don't play properly, only playing the first step. For example. when i load up say the knight rider or 808 groover patches from mod 3 or mod 2 they only play the first step of each patern on the mds and the patern seq goes down each beat. You just get this da.da.da.da.da.da.da on and on.
sb404 sequencer bug, & Solaris sequencer bug. Pattern can not be changed.
This is scope 5 and 5.1 on xite hardware. On win xp 32 bit.
Hope this can be fixed.
Regards
Hari
...............................
This is the response.
..........................................
yes, these are known bugs that should be fixed in the next Scope release.
Re: Very positive response from support.
Posted: Tue Jan 29, 2013 2:52 pm
by Bud Weiser
Liquid EDGE wrote:
This is the response.
..........................................
yes, these are known bugs that should be fixed in the next Scope release.
Excellent !
Thx for posting.
Bud
Re: Very positive response from support.
Posted: Tue Jan 29, 2013 3:51 pm
by Eanna
Great news! Thanks for reporting back.
Your description of the symptoms reminds me of this...
Re: Very positive response from support.
Posted: Tue Jan 29, 2013 5:08 pm
by dante
Good news !
Re: Very positive response from support.
Posted: Wed Jan 30, 2013 4:48 am
by Sounddesigner
Definitely good to hear. Thanks for posting!
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 9:33 am
by nitri
Hello, was corrected?
Or you know`any solution?
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 9:46 am
by petal
There has been no new release of Scope since the original posting, so no solution yet.
Also, no info on when to expect the next version of Scope has been released either, other than it's "almost done" - dare I say soon?
In the mean time, the only known solution is to install Scope v4.5 or earlier if you have a PCI system.
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 11:55 am
by jksuperstar
Hopefully it's soon. It's getting very wet here in Denver, prime time to spend in the studio. I could use some stock sequencers in Modular about now
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 1:10 pm
by dante
jksuperstar wrote:Hopefully it's soon. It's getting very wet here in Denver, prime time to spend in the studio. I could use some stock sequencers in Modular about now
There's always Mattomat. 'Soon' should be NAMM 2014. If not, then another year I spose
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 2:58 pm
by garyb
- relax it will be over soon.jpg (88.57 KiB) Viewed 4601 times
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 3:49 pm
by capacitor
jksuperstar wrote:Hopefully it's soon. It's getting very wet here in Denver, prime time to spend in the studio. I could use some stock sequencers in Modular about now
It's still coming down here in Boulder. Pretty amazing. We were all hoping for a little rain a few days back.
Re: Very positive response from support.
Posted: Thu Sep 12, 2013 3:54 pm
by jksuperstar
Sequencers inside a modular are or can be very different animals from a typical loop-sequencer. FleXor is a good appetizer for now.
Re: Very positive response from support.
Posted: Fri Sep 13, 2013 11:30 pm
by Liquid EDGE
petal wrote:There has been no new release of Scope since the original posting, so no solution yet.
Also, no info on when to expect the next version of Scope has been released either, other than it's "almost done" - dare I say soon?
In the mean time, the only known solution is to install Scope v4.5 or earlier if you have a PCI system.
The issue is only on xite. Version 5 or 5.1 for pci is fine.
Re: Very positive response from support.
Posted: Sat Sep 14, 2013 8:51 am
by garyb
hopefully everyone in Colorado is ok and not flooded out...