midi output

virtualstudio · Post by **virtualstudio** » Sun May 14, 2006 12:57 pm

Hi

I have no midi output from a selected midi channel in cubase. midi is comming in. playback is also ok all midi tracks play .

my projekt is ok: scope midi source <> seq dest.
seq source <>devices

must be a setting in cubase??

thanks

[ This Message was edited by: virtualstudio on 2006-05-14 13:58 ]

at0m · Post by **at0m** » Sun May 14, 2006 2:46 pm

Did you enable MIDI monitoring in Cubase on that track ?
Did you set up any filters (see Cubase > File > Preferences > MIDI filters ?

--

Just as a note, I don't use MIDI monitoring personally if I can avoid it. I prefer to keep on Scope what's already there:

Scope MIDI Source + Seq Source 1 > Merger > Project
and
Scope MIDI Source > Seq Dest 1

Unless changing MIDI channel on the harware keyboard/controller would be difficult of course. That routing makes sure I don't need a sequencer open to throw in a synth and play it, and avoids any additional latency as the setup you described above...

Just a hint, choose whatever you feel confortable with of course

virtualstudio · Post by **virtualstudio** » Mon May 15, 2006 4:16 am

On 2006-05-14 15:46, at0m wrote:
Did you enable MIDI monitoring in Cubase on that track ?

--

Unless changing MIDI channel on the harware keyboard/controller would be difficult of course. .......

where ?? do I enable that?

I use a roland d20 as midi keyboard I have no idea how to change the channel number.....edit:found the manual and found it

I'll have to route it your way
thanks!!

[ This Message was edited by: virtualstudio on 2006-05-15 05:32 ]

at0m · Post by **at0m** » Mon May 15, 2006 4:28 am

On each cubase track there's a grey speaker button that turns kind of orange when clicked. When orange, the channel's input (receiving on omni channel) is forwarded to the channel's output port and channel, except for the things filtered in the Preferences dialog.

If you don't see the speaker, it's also on the mixer...

virtualstudio · Post by **virtualstudio** » Mon May 15, 2006 5:47 am

now I've set it up your way
I see the midi note comming in on the transportbar from cubase, but its not recording?!?!something is wrong here !

can this have something to do with changing my system to standaard pc mode(after telephone call with CW support)
or is it just some cubase setting I don't see

at0m · Post by **at0m** » Mon May 15, 2006 5:58 am

Did you arm the track for recording?

Maybe you should browse through Cubase's manual a bit, it explains how to route, monitor and record MIDI in SX. Your Scope setup seems to do just fine...

virtualstudio · Post by **virtualstudio** » Mon May 15, 2006 6:13 am

I know I've worked like this all the time.

only after problems with my system I've reinstalled everything a few times.

I did get a strange message from a old projekt: somthing about midi settings(?) that it would only work after restarting window's

[ This Message was edited by: virtualstudio on 2006-05-15 07:13 ]

at0m · Post by **at0m** » Mon May 15, 2006 6:16 am

Did you load all midi seq's/destinations into the project as in Scope's properties in Computer/Device Management? If it says "3" there, load 3 of each in the project... Not sure if that would solve the problem though.

virtualstudio · Post by **virtualstudio** » Wed May 17, 2006 12:44 pm

thanks At0m

i found now that after making new projekt in cubase everything is fine.
so it must be somthing in the projekt settings from cubase !